AE Modular
POLAMIX Module a 3-Channel Attenuverter/Mixer for AE Modular
POLAMIX Module a 3-Channel Attenuverter/Mixer for AE Modular
Tangible waves launched a new CV Utility Module.
The POLAMIX is similar to the 2CVTOOL in that you can offset and -/+ attenuate CV signals, but it also acts as a 3 channel mixer. Try to use this with 3 LFOs for modulation mayhem!
The three inputs are routed to corresponding knobs, where the center position means a level of zero. Turning the level knob to the right increases the level of the input signal; turning it to the left, the level is also increased, but inverted. E.G. when feeding a sawtooth signal to the input, you can get either a rising or falling signal at the output. And this for each of the three inputs. Finally, with the offset knob, the total level can be shifted up or down.
Pricing and Availability
POLAMIX is available now at the AE Modular / Tangible waves shop.
AE Modular
Available now – Cable Management Kit for AE MODULAR
AE Modular Bread Board Cable Holders by Flavorwave
As reported earlier AE Modular Bread Board Cable Holders by Flavorwave was planned to be ready for order and shipment in May 2021. The cable management kit it is designed for one row of an AE rack. With the Wings used in the studio, and the tabs for travel. The main reason for the difference is that the wings stick off the rack about two inches and could break during travel, but the tabs would not.
The cable hanger “wings” attach in various ways to your AE Modular rack case via the M5 and M3 screw holes. ( see diagram) The slanted grooves keep your bread board cables in reach, but organized and out of your way. The larger groove can accommodate 3.5mm audio or patch cables or your midi cables.
The “Patch Tabs” and Velcro strap help keep your patches safe when traveling, from accidental unplugs, or curious studio cats. The velcro strap runs the length of the case over the connections, providing enough protection without providing pressure that could damage the connections or cables.
Kit Includes
- One Cable Wing (left or right facing)
- One Patch Tab
- One Velcro Strap
- Necessary screws to attach them
- Flavorwave Sticker
These kits are made by myself at a community workshop. Not a giant factory, please be patient if something is sold out. They are laser-cut acrylic.
Pricing and Availability
CABLE MANAGEMENT KIT for AE MODULAR is available now.
AE Modular
AE Modular Bread Board Cable Holders by Flavorwave in May 2021
Coming this May…
This cable management is for my loose AE Modular cables that are sitting beside your racks in a box. Check it out on Flavorwave’s Online Shop. Flavorwave’s first product is a cable management kit for the Tangible Waves AE Modular Synth format. It includes a breadboard cable hanger, and “Patch Tabs” that help hold cable patches in place.
Essentially it is designed for one row of an AE rack. With the Wings used in studio, and the tabs for travel. The main reason for the difference is that the wings stick off the rack about two inches and could break during travel, but the tabs would not.
AE Modular
AE Modular 2TONE New Module
2TONE Module (AE Modular)
2TONE is a dual bass-treble tone control, that is a quite useful companion for the MIXCONSOLE, to shape the overall spectrum of individual signal paths.
-
Music Theory3 months ago
Unlocking Nature’s Harmony: The Power of 432 Hz Frequency in Sound & Music for Enhanced Living and Well-Being
-
Sound Design3 months ago
What Is the Difference Between a Sound Engineer and A Sound Designer?
-
Native Instruments Kontakt3 months ago
VOCAL AI – Animated Intelligence: The Ultimate Vocal Playground
-
Sound Design3 months ago
Why Sound Engineer
-
Expert Guides3 months ago
How to Become a Sound Designer for Film
-
Expert Guides3 months ago
How Do You Become a Sound Designer
-
Composing3 months ago
Drums in Trailer Music: The Impactful Sound of Cinematic Percussion
-
Field Recording3 months ago
Discover the Top Contact Microphones for Field Recording – Capture Crisp Audio Outdoors!